Home | Links | Contact |

Printed from www.nzmeccano.com

Top Home Bottom

Universal Joints Explained by Peter Stuart

(Author: Peter Stuart)

by Peter Stuart, Meccano Modellers Association Sydney Inc

Universal Joints Explained

by Peter Stuart, Meccano Modellers Association Sydney Inc

 

Universal joints (UJs) do not transmit constant rotary motion when driving through any angle other than a straight line (zero angle). When driving though an angle, a UJ imparts a cyclical faster and slower rotation to the driven shaft on each half revolution. The amount of this speed variation is dependent on the angle; the greater the angle, the greater the speed variation.

 

It can be calculated that at an angle of 25 degrees, a UJ rotating at 100rpm will cause the driven shaft to briefly reach a maximum speed of 110rpm in the first quarter revolution then drop briefly to 91rpm in the second quarter. This higher and lower speed variation will be repeated in the next two quarter revolutions.

 

Speed variation causes vibration and noise, and wears out the bearings. So what can be done?

1. Keep the angle of the UJ less than 25 degrees.
2. UJs should always be used in pairs so that three shafts are involved; input, intermediate and output. If the input and output shafts are made parallel then the angle though which the two UJs will be driving will be the same. Diagram 1 shows angle A to be the same for both UJs.
3. Align the forks of the two UJs so that the second UJ will cancel the speed variation caused by the first UJ. It is true that the intermediate shaft will rotate with speed variation, but not the output shaft. Correct alignment is achieved by having the forks aligned at each end of the intermediate shaft in line with each other. Diagram 1 shows this. Another way to picture the arrangement is that the second UJ is installed as a mirror image of the first.

Provided the angles through which the two UJs are operating is the same, another arrangement is possible as shown in Diagram 2. If a drive has to go around a corner of say 30 degrees, then two UJs can be used provided each joint turns the drive through half the angle; 15 degrees in this example (angle B in the diagram). The alignment of forks still has to be the same as described above. The intermediate shaft can be short; in fact so short that the bosses butt against each other. This double universal joint arrangement can be seen in the final drive of articulated earth-moving machinery with all-wheel-drive.

 

Rear-wheel- drive vehicles have UJs at either end of their tail shaft, taking the drive from the gearbox to the differential. The gearbox shaft and the differential pinion shaft are kept parallel as much as the rear suspension will allow, and the forks of these UJs must be aligned as already explained. The arrangement can often be viewed on large trucks where the driveline is exposed.

Speed variation is the reason why UJs are not used in the drive shafts of front-wheel-drive vehicles. So-called Constant Velocity (CV) joints are used instead, to allow the front wheels to steer while the wheels are being driven. However, CV joints are expensive to manufacture and are not available in the small sizes needed for Meccano models.

Mick Berg      (at 7:35am, Fri 19th Oct, 18)

Very interesting info. Thank you!


Your name:
Your message:
Security check: (Please type in the text to prove you're a person!)
 
Login status:  You have not yet entered your user name and password. You cannot create or edit documents until you do.
Enter your user name and password to log in

Remember me

If you click on the box marked 'remember me next time', you will not have to log in again on this computer for three months.

If you don't have a user name yet, please click here

Latest documents:

 
(Neil Bedford and Richard Smith)
Midlands Meccano Guild
Model Report 
97th Meeting 
 
The Arduino Sketch 
and how to upload a Youtube or Vimeo video to the Gallery 
(Paulo Kroeff de Souza)
"Homemade" Screwed Rods
 
(Paulo Kroeff de Souza)
The Meccano driving band problem
 
(Paulo Kroeff de Souza)
Meccano Cord Reproduction
 
(Paulo Kroeff de Souza)
Substitutes for parts 142 and 155
 
(Philip Drew & Richard Smith)
Midlands Meccano Guild
105th Model Report 
92nd Model Report 
(Neil Bedford and John Rogers)
Midlands Meccano Guild
104th Model Report 
91st Model Report 
 
103rd Meeting Model Report 
by Peter Stuart, Meccano Modellers Association Sydney Inc 
(Richard Smith and Neil Bedford)
Midlands Meccano Guild
102nd Meeting Model Report 
(John Rogers & Colin Bull)
Midlands Meccano Guild
101st Meeting Model Report 
Spanner Challenge 
(John Rogers and Neil Bedford)
Midlands Meccano Guild
100th Meeting Model Report 
 
A G gauge model 
(Colin Bull & Richard Smith)
Midlands Meccano Guild
99th Meeting Model Report 
98th Meeting Model Report 
 
97th Meeting Model Report 
(David Couch)
The Little Tram
An introductory Arduino project 
(G. Eiermann and M. Schild)
A Short History of MARKLIN Metall
 
96th Meeting Model Report 
83rd Meeting Model Report 
 
82nd Meeting Model Report 
Picks up three golf balls 
(Roger Marriott)
Midlands Meccano Guild
95th Meeting Model Report 
The Spanner Challenge 
 
 
94th Meeting Report 
(Andre Theberge)
Meccano Segway
Instructions 
(Andre Theberge)
A Meccano Segway
Arduino code 
(Andre Theberge)
A Meccano Segway
Assembly instructions 
(Michael J. Walker)
Meet the new MMG President
Geoff Wright 
The Spanner Challenge 
(Michael Walker)
Midlands Meccano Guild
93rd Model Report 
Report by Michael J. Walker. 
92nd Model Report 
(Stan Knight)
Minimal Meccano
Pocket Meccano Sets of the 1970s 
Little Lever, Bolton 
The Spanner Challenge 
91st Model Report 
(Bob Thompson)
Back to the beginning
Shop Display Model 
90th Meeting Report 
(Old Blue Gold)
Getting Old
A screwy story 
The Spanner Challenge 
Model report written by Michael J. Walker 
76th Meeting Report 
Exhibition in Nelson, New Zealand 
(Barry Gerdes)
Meccano Radio
 
 
How to flatten  
(Rod Socket)
Dear Mrs Spanner
Survival techniques for the Meccanoman's wife 
(Stan Knight)
The Top Ten Tools
Indispensable Tools for the Meccanoman 
A call for help 
The Spanner Challenge 
 
For small brass and nickel parts. Also for stripping paint and rotted zinc plating. 
(Stephen Heafield)
Waterslide Transfers
Refurbishing 0 & 00 Aero Models 
Construction details 
or Put Your Hammer Away 
Mobile Morris Crane from 1968 MM 
Bert Love's Blocksetter in colour 
The dangers of internet auctions 
(Rob Thompson pp Terry Bullingh)
BlockSetter Tower
Built by Terry Bullingham 
(Rob Thompson pp John Reid)
Captain Robert Falcon Scott
1912 Polar Sledging Party 
(Niels Gottlob)
Bucket Wheel Excavator
Transcribed from typed document with photos 
Selected Spanner messages 18th to 24th January 
Selected Spanner messages 11th to 17th January 
Selected Spanner messages 4th to 10th January 
 
(Norbert Klimmek)
Hulett Ore Unloader
A 1 to 32 Scale Model 
 
(Joe Attard of Malta)
A model ship
 
 
 
(Arup Dasgupta (ISM 652))
My E15R Motor
A repair story 
(Charles)
About Meccano
What is Meccano? 
Thoughts about modern Meccano 
Some hints and tips 
Not many in this condition I'll bet! 
 
 View all | Chat | Models | Hints and Tips | Opinion | Reviews | Mine