Top Home Bottom

Part 52a-74: Flat plates

52a	Flat plate, 5½'' x 3½''	1919	-	8	11	6	N°9
53a	Flat plate, 4½'' x 2½''	1919	-	3	6	4	N°9
70	Flat plate, 5½'' x 2½''	1918	-	6	7	4	N°9
72	Flat plate, 2½'' x 2½''	1918	-	4	4	2	N°10
73	Flat plate, 3'' x 1½''	1931	-	n/a	0	2	N°10
74	Flat plate, 1½'' x 1½''	1962	-	n/a	n/a	n/a	n/a

The parts

A strange set of numbers, but there is some logic. The first flat plates were introduced in early 1918 (according to Vol.6), as parts 70 and 72. They could have existed in 1917, but there was no manual printing or mention of them during that year. There was no part 71, but Meccano had started to use blocks of ten part numbers for each type of part. At the same time, the 80's were reserved for screwed rods. Perhaps a blank was left for a future size?

In 1919, perhaps after having realised how useful the new flat plates were, the top two in the table above were introduced. This was of course a very easy job, as they were already being made as the flanged plates part 52 and 53. The parts were simply removed from the production line before bending and marketed as parts 52a and 53a, introduced into the Inventor's Outfit B of 1919. You can see from the picture above that part 53a has elongated holes at each end (matching the holes in the flanges of part 53), and part 52a is just an unfolded part 52 (which of course had only two long flanges at the time).

These parts were only available in the Inventor's Outfit, until the large-scale redesign of the outfits in 1922. Even so, they were only supplied in the largest of outfits, which continued as you can see from the last column in the table. Post-war outfits contained no flat plates at all until outfit 9. In 1962, part 53a (4½'' x 2½'' flat plate) found its way down as far as outfit 4, but the other parts remained only in 9's and 10's.

Chronological variations

One of the very rare sets of parts that have remained completely unchanged from their introduction during WW1 through to the end of UK production, and even later in French outfits. Nothing more to tell, I don't think!

Variations and oddities

Here's an unusual one. A dark blue flat plate, stamped as expected, provided by Richard Payn. He has a number of these, but they're considered to be specials from the model room at Binns Road, or perhaps experimental parts. The dark blue is the normal 78/79 dark blue colour.

Dealer spare parts boxes

In the same way as the flanged plates, 1950's boxes for these parts didn't match the size of the parts inside. Boxes generally contained 6 of each part, but you can see from the picture to the right that the mid-50's part 72s are only half the size of the box itself. The later light red part 74s (only introduced in 1962), are in a box that fits them exactly.

Individual part numbers

Part numbers for the parts on this page are as follows:    Unique part numbers
For identification, each variation has been given a suffix to the main Meccano part number. These suffixes consist of a two-character code for the colour, and if there are many variations, a further number and sometimes letter code to identify each variation. See the bottom of the 'Parts' page for further details.

You don't need to worry what the codes are, just click on any one for a photograph.

The button above turns on and off the display of DMS numbers (where they are known). The DMS (Development of the Meccano System, Hauton and Hindemarsh) published in 1972 and added to in 75 and 82, suggested part numbers for every variation of every Meccano part. These numbers aren't perfect, but they are recognised and also referenced in the EMP (Encyclopedia of Meccano Parts, Don Blakeborough).

Description	from	52a	53a	70	72	73	74
Nickel plated, 20swg plate ¹	18	.ni	.ni	.ni	.ni	.ni
Early red (pea-red)	26	.re	.re	.re	.re
Dark red	27	.dr	.dr	.dr	.dr	.dr
Blue with gold crosshatching	34	.bg	.bg	.bg	.bg	.bg
Medium red	37	.mr1	.mr1	.mr1	.mr1	.mr1
Medium red with post-war markings	45	.mr	.mr	.mr	.mr	.mr
Light red	58	.lr	.lr	.lr	.lr	.lr	.lr
Yellow	64	.ye	.ye	.ye	.ye	.ye	.ye
Olive green (Army Multikit) †	73-79			.am
Dark yellow	79	.dy	.dy	.dy	.dy	.dy	.dy
		ALL	ALL	ALL	ALL	ALL	ALL

Note: ¹ Part 73 didn't appear in nickel plate, being introduced in 1931. However, outfits and parts could be special-ordered in a nickel finish up to 1941, and for this reason there are a tiny number of nickel plated ones even though it was only supplied in outfit 10s of the period. Part 73.ni is about as rare as Meccano parts get.

Please send us pictures of missing parts! Hints and tips for pictures
Take a picture of the part in very good light, preferably on a plain yellow background, without a flash but with a tripod.
Ideally, trim the picture to about 150 pixels per inch of the Meccano part (unless the part is particularly big or small), save it as a reasonably good quality jpg file with a filename of exactly the part number, for example 19b.ni1.jpg, and email it to us by clicking on 'Contact us' at the top of the page. Thanks!

• A greyed-out box shows that no part exists for that colour combination.
• Part number codes with a green background have an attached picture of the part, just click once on the code to show a photograph of that part in a separate window.
• Parts marked "†" were temporary or economy parts, or existed only within specific themed outfits. The previous part continued throughout or afterwards.

Further information

Total number of messages on this page: 13.  This is page 3 of 3.   

Jeff Jones      (at 11:27am, Tue 31st Jul, 07)

Meccano History.... I spent years collecting sets etc to work out the order of colours parts etc. We mus concour as I have loads of info that can help your web site. I did re do the DMS so that it and its ommisions were correct up to 1934. I dont know what you need to know but I probably do know. BTW best say the nickel sets were increased in size with flanged plates in october 1910. I have dated sets with this.

Your name:
Your message:
Security check:	(Please type in the text to prove you're a person!)